CHP over run

No. 1 and No. 3
zebra55
Posts: 348
Joined: Tue Feb 02, 2016 6:55 pm
Location: Michigan

CHP over run

Post by zebra55 »

just picked up a 1A CHP over run 357 Mag (no CHP etching). I was wandering if anyone knows how many of these were made? The RENE Reference mentions them, but does not give an estimate on how many were made...
Coogs
Posts: 392
Joined: Fri Jul 04, 2014 8:07 am
Location: NW PA.

Re: CHP over run

Post by Coogs »

I'm thinking 2-300? sounds like a reasonable number I heard one time......then again, I have small bouts of CRS...
Hawkeye28
Posts: 310
Joined: Thu Oct 30, 2014 4:17 pm
Location: Near North Woods

Re: CHP over run

Post by Hawkeye28 »

STEVEN VOGEL TOLD ME THE NUMBER WAS NEAR 200..........
021
Posts: 15
Joined: Tue May 09, 2017 7:28 pm

Re: CHP over run

Post by 021 »

1820 CHP’s and 180 non-. That’s about as good a guess as you’re going to get.
zebra55
Posts: 348
Joined: Tue Feb 02, 2016 6:55 pm
Location: Michigan

Re: CHP over run

Post by zebra55 »

021 wrote: Sun Jul 07, 2019 12:57 pm 1820 CHP’s and 180 non-. That’s about as good a guess as you’re going to get.
thanks to all for the information. Hey 021 was wondering where that info came from??
021
Posts: 15
Joined: Tue May 09, 2017 7:28 pm

Re: CHP over run

Post by 021 »

Ruger won't tell you how many this or that they have made, but people on forums that I access and knowledgeable souls I talk to who would know-if anyone knows, have stated this in the past and I tend to believe them since they have been correct on other issues. But as I said---best guess. I am somewhat of a No.1 collector and have four of the little .357's, sweet pieces of machinery. Regards, 021
chet15
Posts: 734
Joined: Sat Aug 16, 2014 11:28 am

Re: CHP over run

Post by chet15 »

I still really disagree with that number.
I have seen by far more non-marked CHP's than those with the bicycle wheel on them.
180 isn't much. In fact, you'd be a lot more hard pressed to find a 6-1/2" .41 Mag. Blackhawk with factory installed brass grip frame of which there were supposedly 160 made.
Just noting my observances.
Chet15
zebra55
Posts: 348
Joined: Tue Feb 02, 2016 6:55 pm
Location: Michigan

Re: CHP over run

Post by zebra55 »

chet15 wrote: Tue Jul 09, 2019 2:18 pm I still really disagree with that number.
I have seen by far more non-marked CHP's than those with the bicycle wheel on them.
180 isn't much. In fact, you'd be a lot more hard pressed to find a 6-1/2" .41 Mag. Blackhawk with factory installed brass grip frame of which there were supposedly 160 made.
Just noting my observances.
Chet15
Chad
what is your estimate then???
chet15
Posts: 734
Joined: Sat Aug 16, 2014 11:28 am

Re: CHP over run

Post by chet15 »

A good question.
The hitch in that would be that of those that were supposedly sold to the CHP, how many of those remain in CHP gun safes?
I wouldn't be able to hazard a guess. Other then I've noted probably at least twice as many non-marked #1's in .357 as I have BKH42B's.
And the next thing is, the BKH42B sticks out like a sore thumb. The #1 not so much, especially without having the CHP rollmark.
Chet15
rugerguy
Posts: 194
Joined: Tue Jul 01, 2014 1:57 pm
Location: NE OHio

Re: CHP over run

Post by rugerguy »

I've had a few of the both the overrun as well as the Highpatrol model and in either case was always a tough sell, not many folks wanted a 357 magnum in a single shot rifle, for the MOST part, they were NOT collectors, and this was always at the OGCA over the years :|
in fact I recall my gunsmith rechambered one to 357 Maximum,and NO, did NOT "remark" the chamber,,,,never did with the 32 H&R Mag when he punched them out to 327 Fed Mag......hhmmmmm...so they are out there :roll:
Post Reply